Ford Galaxy Central Locking Wiring Diagram
Content .. 873 874 875 876 ..
Ford Galaxy / Ford S-MAX. Manual - part 875
GO to E4
.
No
LOCATE and REPAIR the break in circuit CPL02A (BK)
between the driver door module and the driver door
lock with the aid of the Wiring Diagrams. CHECK the
operation of the system.
E3: CHECK FOR A BREAK IN THE CIRCUIT BETWEEN THE DRIVER DOOR MODULE AND
THE DRIVER DOOR LOCK
Ignition switch in position 0.
1
Measure the resistance between the driver door
module connector C5PL01-A pin 10, circuit CPL02AA
(BK), wiring harness side and the driver door lock
connector C5PL63 pin 5, circuit CPL02AA (BK), wiring
harness side.
2
Is a resistance of less than 2 Ohm measured?
Yes
GO to E4
.
No
LOCATE and REPAIR the break in circuit CPL02AA
(BK) between the driver door module and the driver
door lock with the aid of the Wiring Diagrams. CHECK
the operation of the system.
E4: CHECK FOR SHORT TO GROUND BETWEEN THE DRIVER DOOR MODULE AND THE
DRIVER DOOR LOCK
Measure the resistance between:
the driver door module connector C5PL01-A pin 10,
circuit CPL02A (BK), wiring harness side and
ground (LHD).
or
the driver door module connector C5PL01-A pin 10,
circuit CPL02AA (BK), wiring harness side and
ground (RHD).
1
Is a resistance of more than 10,000 ohms measured?
Yes
LHD vehicles:
GO to E5
.
RHD vehicles:
GO to E7
.
No
LOCATE and REPAIR the short to ground in the circuit
between the driver door module and the driver door
lock with the aid of the Wiring Diagrams. CHECK the
operation of the system.
E5: CHECK THE VOLTAGE AT THE DRIVER DOOR LOCK (DURING
LOCKING/UNLOCKING
Connect driver door module C5PL01-A.
1
Measure the voltage between the driver door lock
connector C5PL63 pin 7, circuit CPL02A (BK), wiring
harness side and ground.
2
Lock and unlock the vehicle with the key in the door
lock cylinder.
3
Is battery voltage measured during unlocking?
Yes
GO to E6
.
No
CHECK and if necessary INSTALL a new driver door
module. CHECK the operation of the system.
E6: CHECK THE VOLTAGE AT THE DRIVER DOOR LOCK (DURING DOUBLE
LOCKING/UNLOCKING)
Measure the voltage between the driver door lock
connector C6PL63 pin 7, circuit CPL02A (BK), wiring
harness side and ground.
1
Double lock and unlock the vehicle with the key in
the door lock cylinder.
2
Is battery voltage measured during unlocking?
Yes
CHECK and if necessary INSTALL a new driver door
lock. CHECK the operation of the system.
No
CHECK and if necessary INSTALL a new driver door
module. CHECK the operation of the system.
E7: CHECK THE VOLTAGE AT THE DRIVER DOOR LOCK (DURING
LOCKING/UNLOCKING)
Connect driver door module C5PL01-A.
1
Measure the voltage between the driver door lock
connector C5PL63 pin 5, circuit CPL02AA (BK), wiring
harness side and ground.
2
Lock and unlock the vehicle with the key in the door
lock cylinder.
3
Is battery voltage measured during unlocking?
Yes
GO to E8
.
No
CHECK and if necessary INSTALL a new driver door
module. CHECK the operation of the system.
E8: CHECK THE VOLTAGE AT THE DRIVER DOOR LOCK (DURING DOUBLE
LOCKING/UNLOCKING)
Measure the voltage between the driver door lock
connector C5PL63 pin 5, circuit CPL02AA (BK), wiring
harness side and ground.
1
Double lock and unlock the vehicle with the key in
the door lock cylinder.
2
Is battery voltage measured during unlocking?
Yes
CHECK and if necessary INSTALL a new driver door
lock. CHECK the operation of the system.
No
CHECK and if necessary INSTALL a new driver door
module. CHECK the operation of the system.
PINPOINT TEST F : CIRCUIT OF THE PASSENGER CENTRAL LOCKING
MOTOR WITH DOUBLE LOCKING FAULTY.
WARNING: The window anti-trap function will not operate during the window motor
initialization procedure.
NOTE: If the power to a window regulator motor has been disconnected, it is necessary
to initialize that window regulator motor.
TEST CONDITIONS
DETAILS/RESULTS/ACTIONS
F1: CHECK FOR SHORT TO VOLTAGE BETWEEN THE PASSENGER DOOR MODULE AND
THE PASSENGER DOOR LOCK
Disconnect passenger door module C6PL01-A.
1
Disconnect passenger door lock C6PL64.
2
Ignition switch in position II.
3
Measure the voltage between:
the passenger door module connector C6PL01-A
pin 10, circuit CPL65A (BK), wiring harness side
and ground (LHD).
or
the passenger door module connector C6PL01-A
pin 10, circuit CPL65AA (BK), wiring harness side
and ground (RHD).
4
Is a voltage measured?
Yes
LOCATE and REPAIR the short to voltage in the
circuit between the passenger door module and the
passenger door lock with the aid of the Wiring
Diagrams. CHECK the operation of the system.
No
LHD vehicles:
GO to F2
.
RHD vehicles:
GO to F3
.
F2: CHECK FOR A BREAK IN THE CIRCUIT BETWEEN THE PASSENGER DOOR MODULE
AND THE PASSENGER DOOR LOCK
Ignition switch in position 0.
1
Measure the resistance between the passenger door
module connector C6PL01-A pin 10, circuit CPL65A
(BK), wiring harness side and the passenger door
lock connector C6PL64 pin 5, circuit CPL65A (BK),
wiring harness side.
2
Is a resistance of less than 2 Ohm measured?
Yes
GO to F4
.
No
LOCATE and REPAIR the break in circuit CPL65A (BK)
between the passenger door module and the
passenger door lock with the aid of the Wiring
Diagrams. CHECK the operation of the system.
F3: CHECK FOR A BREAK IN THE CIRCUIT BETWEEN THE PASSENGER DOOR MODULE
AND THE PASSENGER DOOR LOCK
Ignition switch in position 0.
1
Measure the resistance between the passenger door
module connector C6PL01-A pin 10, circuit CPL65AA
(BK), wiring harness side and the passenger door
lock connector C6PL64 pin 7, circuit CPL65AA (BK),
wiring harness side.
2
Is a resistance of less than 2 Ohm measured?
Yes
GO to F4
.
No
LOCATE and REPAIR the break in circuit CPL65AA
(BK) between the passenger door module and the
passenger door lock with the aid of the Wiring
Diagrams. CHECK the operation of the system.
F4: CHECK FOR SHORT TO GROUND BETWEEN THE PASSENGER DOOR MODULE AND
THE PASSENGER DOOR LOCK
Ignition switch in position 0.
1
Measure the resistance between:
the passenger door module connector C6PL01-A,
pin 10, circuit CPL65A (BK), wiring harness side
and ground.
or
the passenger door module connector C6PL01-A
pin 10, circuit CPL65AA (BK), wiring harness side
and ground.
2
Is a resistance of more than 10,000 ohms measured?
Yes
Content .. 873 874 875 876 ..
Source: https://zinref.ru/avtomobili/Ford/905_00_Ford%20Galaxy_Ford%20S-MAX_%202006_english/875.htm
Posted by: irarerealstate.blogspot.com